- THE SHOP
- >
- Tanks, Atomisers and Clearomisers
- >
- JOMO Tech Lite 76ers Tank
JOMO Tech Lite 76ers Tank
SKU:
A$35.00
A$35.00
Unavailable
per item
There's no need to restrict this neat little tank to use with the Lite 76ers MOD . . . it's very capable of pairing with other machines [Kanger Tech Cupti 2 or Royal 100 for example] if you roll that way.
It will handle from 1W - 76W of power and the full gauntlet of the temperature control range [100c - 300c]. Generally, she runs on a 0.4 ohm SS coil, mainly because it has a broader power range than it's Ti and Ni associates [30W - 75W].
She's a top filling tank [2ml capacity] with an integrated air flow control valve in the base. To replace the coil, you again work from the top of the tank.
The special feature of this tank however, would be the child lock design. Just like with any other child proof bottle, to release the child lock you need to press down and turn the top layer of the top cap assembly. To reset the child lock after filling or replacing the coil, again you press down on the top layer of the top cap assembly and turn.
It will handle from 1W - 76W of power and the full gauntlet of the temperature control range [100c - 300c]. Generally, she runs on a 0.4 ohm SS coil, mainly because it has a broader power range than it's Ti and Ni associates [30W - 75W].
She's a top filling tank [2ml capacity] with an integrated air flow control valve in the base. To replace the coil, you again work from the top of the tank.
The special feature of this tank however, would be the child lock design. Just like with any other child proof bottle, to release the child lock you need to press down and turn the top layer of the top cap assembly. To reset the child lock after filling or replacing the coil, again you press down on the top layer of the top cap assembly and turn.
-
Description
-
Filling the Tank
-
Changing the Coil
-
Specifications
-
Reviews
<
>
Standing a petite 37mm tall, she has a slim 22mm diameter, which means you'll rarely have any problems with the tank hanging over the side of your MOD. Oh and yes, it does crank out the vapor, in case you were wondering.
Adjusting the Air Flow : As with all of the latest tank technology, the air flow adjustment on the base of the tank allows you to fine tune your vape. Open up the air flow by rotating the control ring and exposing more of the slot, allowing more air into the mix which gives an easy draw and more vapor. Close the air flow by rotating the control ring and covering the slot, restricting the air coming in and making a tighter draw and less vapor. Available in Stainless Steel with Black Seals or Pink Seals |
Filling the Tank :
When filling the tank, make sure that the air flow is closed off.
1. Push down on the mouthpiece assembly and turn to release the child lock
2. Unscrew and remove the mouthpiece assembly
3. You'll see that there are 2 slots and 1 round hole in the top plate. Direct the tip of your needle bottle to one or the other of the slots and fill to just below the top plate. Do not fill past the top plate. Do not pour liquid into the centre round hole : it's the air tube so you'll end up sucking up any liquid that's in that tube. You can clean it out with a twisted paper towel or cotton bud before you screw the mouthpiece assembly back on
4. Replace the mouthpiece assembly and screw on securely
5. Press down and turn the mouthpiece assembly to reset the child lock
When filling the tank, make sure that the air flow is closed off.
1. Push down on the mouthpiece assembly and turn to release the child lock
2. Unscrew and remove the mouthpiece assembly
3. You'll see that there are 2 slots and 1 round hole in the top plate. Direct the tip of your needle bottle to one or the other of the slots and fill to just below the top plate. Do not fill past the top plate. Do not pour liquid into the centre round hole : it's the air tube so you'll end up sucking up any liquid that's in that tube. You can clean it out with a twisted paper towel or cotton bud before you screw the mouthpiece assembly back on
4. Replace the mouthpiece assembly and screw on securely
5. Press down and turn the mouthpiece assembly to reset the child lock
To replace the Coil :
1. Push down on the mouthpiece assembly and turn to release the child lock
2. Unscrew and remove the mouthpiece assembly
3. Unscrew and remove the top plate
4. You've now got direct access to the coil, so unscrew and remove it
5. Prime the replacement coil and then screw it securely into place
6. Now it's just a matter of putting the tank back together. Replace and screw on the top plate, then the mouthpiece assembly
7. Press down and turn the mouthpiece assembly to reset the child lock
1. Push down on the mouthpiece assembly and turn to release the child lock
2. Unscrew and remove the mouthpiece assembly
3. Unscrew and remove the top plate
4. You've now got direct access to the coil, so unscrew and remove it
5. Prime the replacement coil and then screw it securely into place
6. Now it's just a matter of putting the tank back together. Replace and screw on the top plate, then the mouthpiece assembly
7. Press down and turn the mouthpiece assembly to reset the child lock
Important Bits You Need To Remember About The Coils [Pay attention now, this stuff is really important, seriously]
* NEVER dry fire these coils. If you hit the fire button when the coil isn't immersed in liquid, you'll just burn it out, pretty much instantly : it only takes a couple of seconds to burn when it's completely dry and just as a side note, it absolutely reeks when it burns and the smell hangs around for a while too . . . nasty . . .
* NEVER let the liquid level in the Tank fall below the round holes in the sides of the coil [the priming holes if you like]. If the liquid level does fall below the holes, the Organic Cotton inside the coil will begin to dry out. Do not use the unit until you've refilled the Tank and the coil is totally immersed in liquid again. Best practice is to never let the Tank liquid level fall below 1/4 of a Tank.
* Prime each new coil and let the unit stand for a few minutes after filling to ensure that all of the Organic Cotton inside the coil body becomes completely wet. You may notice that the liquid level will go down fairly dramatically when you put in a new coil : remember to make sure that once the coil is fully wet, there is still enough liquid in the Tank to completely cover the coil or more specifically, the priming holes at the very least.
* Best practice is to use a cloth or tissue to remove the spent coil, they're best not grabbed bare handed cause it'll be covered in liquid and you don't want to get liquid on your hands if you can help it. You can also go for tweezers or pliers to remove the coils and when you put the new coil in, you can tighten it with the tweezers or pliers but take care not to damage the coil or over tighten it.
If you are going to remove and replace the coil by hand only, be aware that the top of the coil can be sharp [because of the thread cut into it, there can be a sharp point where the thread starts], so take care not to cut yourself. Remember girls and boys, "Safety First" . . .
* It is recommended that the coils be replaced every 2 - 3 weeks, however, JOMO Tech goes further to suggest that the coils be cleaned in warm water, not boiling, weekly if the user is a very heavy vaper.
If you go with the bathing the coil ritual, it is suggested that you can extend the coil life in excess of a month or so.
PLEASE NOTE : If you do go with the bathing ritual, the coils must be completely dry before you return them to use and washed coils will need to be primed again before being used.
Just as a side note and a bit of a Captain Obvious moment, but make sure you dispose of spent coils by wrapping them up or sealing them in a plastic bag so that any excess liquid will not contaminate your bin.
And here's the second Captain Obvious point : don't leave spent coils anywhere children or pets can access them.
* NEVER dry fire these coils. If you hit the fire button when the coil isn't immersed in liquid, you'll just burn it out, pretty much instantly : it only takes a couple of seconds to burn when it's completely dry and just as a side note, it absolutely reeks when it burns and the smell hangs around for a while too . . . nasty . . .
* NEVER let the liquid level in the Tank fall below the round holes in the sides of the coil [the priming holes if you like]. If the liquid level does fall below the holes, the Organic Cotton inside the coil will begin to dry out. Do not use the unit until you've refilled the Tank and the coil is totally immersed in liquid again. Best practice is to never let the Tank liquid level fall below 1/4 of a Tank.
* Prime each new coil and let the unit stand for a few minutes after filling to ensure that all of the Organic Cotton inside the coil body becomes completely wet. You may notice that the liquid level will go down fairly dramatically when you put in a new coil : remember to make sure that once the coil is fully wet, there is still enough liquid in the Tank to completely cover the coil or more specifically, the priming holes at the very least.
* Best practice is to use a cloth or tissue to remove the spent coil, they're best not grabbed bare handed cause it'll be covered in liquid and you don't want to get liquid on your hands if you can help it. You can also go for tweezers or pliers to remove the coils and when you put the new coil in, you can tighten it with the tweezers or pliers but take care not to damage the coil or over tighten it.
If you are going to remove and replace the coil by hand only, be aware that the top of the coil can be sharp [because of the thread cut into it, there can be a sharp point where the thread starts], so take care not to cut yourself. Remember girls and boys, "Safety First" . . .
* It is recommended that the coils be replaced every 2 - 3 weeks, however, JOMO Tech goes further to suggest that the coils be cleaned in warm water, not boiling, weekly if the user is a very heavy vaper.
If you go with the bathing the coil ritual, it is suggested that you can extend the coil life in excess of a month or so.
PLEASE NOTE : If you do go with the bathing ritual, the coils must be completely dry before you return them to use and washed coils will need to be primed again before being used.
Just as a side note and a bit of a Captain Obvious moment, but make sure you dispose of spent coils by wrapping them up or sealing them in a plastic bag so that any excess liquid will not contaminate your bin.
And here's the second Captain Obvious point : don't leave spent coils anywhere children or pets can access them.
Write Review ×